Type D and Type A hybrid

w47

Member
Joined
Jul 9, 2008
Messages
18
Location
Singapore
hi, i just tried a new hybrid and is kinda good. I think it is like a type A(not really sure cos i nvr tried a type a cube) but it is cheaper.
Type d corners, edge, core and centre + Type A screws and spring.
it is able to cut corners at over 40 degree.

do try it out and giv me any comments(+ve and -ve) and suggestion to improve it.

btw, has anyone made tis hybrid b4?
 
Last edited:
The thing with a type D is it locks up a lot, you can blame this for the pieces, so using the pieces would be a bad idea. The best part about the type D is the screws and springs. So I would try and use those. The trick to combo'ing is getting the good part of cubes, and joining them with the good parts of another cubes.
Therefore I make this suggestion: Try taking the D springs and screws(good parts of D cube), with the A core and A pieces(good parts of A cube).
 
So many people are trying such random hybrids.
My new cube will be...
A core
2 corners from a D, 1 from a C, 3 from an A, 1 from a Diansheng and 1 from a store bought.
2 edges from old A, 2 from A II, 6 from D, 1 from C and 1 from Rubik's
4 screw/spring from new type A, 1 from C and 1 from D


Should be epic.
 
The thing with a type D is it locks up a lot, you can blame this for the pieces, so using the pieces would be a bad idea. The best part about the type D is the screws and springs. So I would try and use those. The trick to combo'ing is getting the good part of cubes, and joining them with the good parts of another cubes.
Therefore I make this suggestion: Try taking the D springs and screws(good parts of D cube), with the A core and A pieces(good parts of A cube).

That's what I use and it's the best cube I ever had, by FAR.

Core: Old type A
Springs/Screws/Centers: Type D
Cubies: Old type A
 
I tried this combo before, I felt it was crap. It was pretty much my worst cube ever, so I quickly disassembled it after maybe one solve.

I don't think any cube can cut over 40 degrees of corners. If it's 45 degrees it is right at the center, so when you move R for example, and U face is at 45 degrees, It can go U or U'.
No matter how loose your cube is, it will pop or lock up before it even reaches 35 degrees, usually a good cube cuts corners just under 30 degrees.
If the measurement is more than a fraction above 30 degrees, then you made a measuring error.

Also, stop posting combo threads, people like different cubes and there are thousands of combos, should I make a thread about:

Crappy springless cube corners
Type W edges
Type V core
Rubik's DIY 2003 mold center cap
Type X centers
BIC pen springs
Home Depot Screws size Z
Lubed with soy sauce?
 
Last edited:
it is able to cut corners at over 40 degree.
You sure about that? I don't think that is possible.....
http://www.speedsolving.com/forum/showthread.php?t=7655

Just so you know, it's possible, my cube actually cut corners from approximatively 40 degrees.
Err I don't believe that. Could you actually make the calculation and then tell us what you get? Or show us a video/picture of it.

And what type of 3x3 do you use? I use an old Type D with and old Type A core and I got arctan (11.7/21.9) = 28.1 degrees.

IMG_0396-1.jpg
 
Last edited:
I tried this combo before, I felt it was crap. It was pretty much my worst cube ever, so I quickly disassembled it after maybe one solve.

I don't think any cube can cut over 40 degrees of corners. If it's 45 degrees it is right at the center, so when you move R for example, and U face is at 45 degrees, It can go U or U'.
No matter how loose your cube is, it will pop or lock up before it even reaches 35 degrees, usually a good cube cuts corners just under 30 degrees.
If the measurement is more than a fraction above 30 degrees, then you made a measuring error.

Also, stop posting combo threads, people like different cubes and there are thousands of combos, should I make a thread about:

Crappy springless cube corners
Type W edges
Type V core
Rubik's DIY 2003 mold center cap
Type X centers
BIC pen springs
Home Depot Screws size Z
Lubed with soy sauce?

Don't temp me.

Seriously: We need a combo sticky here, even though this thread should fit under the one already listed. Come to think of it, all combo could go into the other sticky, but a seperate thread would be nice.
 
Seriously: We need a combo sticky here, even though this thread should fit under the one already listed. Come to think of it, all combo could go into the other sticky, but a seperate thread would be nice.
Agreed.

Hybrid cube threads come up all the time. If we had one sticky a person could just ask a question, and then another person could quote them and answer it. That way you would know who is talking about who's cube. I think the thread would be very useful.
 
it is able to cut corners at over 40 degree.
You sure about that? I don't think that is possible.....
http://www.speedsolving.com/forum/showthread.php?t=7655

Just so you know, it's possible, my cube actually cut corners from approximatively 40 degrees.
Err I don't believe that. Could you actually make the calculation and then tell us what you get? Or show us a video/picture of it.

And what type of 3x3 do you use? I use an old Type D with and old Type A core and I got arctan (11.7/21.9) = 28.1 degrees.

IMG_0396-1.jpg

Here ya go, it's about 42-43 degrees on the vid.

 
Last edited by a moderator:
Back
Top