Some lubing questions

cube_addict0r

Regular
Joined
Apr 10, 2010
Messages
45
Location
Belgium
I've been using this storebought cube since March 2010 now, and never lubed it before. Been doing LOTS of solves ever since, and i also broke it in.

I'm about to get silicon spray tomorrow.

Question 1: Does it matter what silicon spray I'll use? (does it REALLY have to be CRC heavy duty silicon spray?

Question 2: I heard lubing an SB does not make a difference at all. Is that true?

Question 3: Does it really matter how I'll apply the spray? My first idea was to pop an edge piece out and spray the silicon spray directly into the cube, but I heard that this might damage the screws and springs. Is it better to take apart the cube and spray the pieces and let them dry, or is spraying directly into the cube actually not that bad?

Thanks in advance! :)
 
Last edited:
just an add-on on the answers

for the 1st question, just don't use WD-40 or such lubes, use silicone (i use Cyclo not CRC)

for the 2nd one, use vaseline first, then after breaking in, wash it out and apply silicone

for the 3rd, for me i use the "pop an edge and 2 corners, and spray" method for 3x3s, 4x4s and up i use the "take it apart and spray all the pieces" method

hope that helps
 
Thanks koreancuber!

just an add-on on the answers

for the 1st question, just don't use WD-40 or such lubes, use silicone (i use Cyclo not CRC)

for the 2nd one, use vaseline first, then after breaking in, wash it out and apply silicone

for the 3rd, for me i use the "pop an edge and 2 corners, and spray" method for 3x3s, 4x4s and up i use the "take it apart and spray all the pieces" method

hope that helps

Thanks for the answers! Is it necessary to use vaseline first or can I skip the vaseline part and apply silicon spray immediately? I'm not that fond of vaseline as I heard it might eat away at the plastic.
 
Is it necessary to use vaseline first or can I skip the vaseline part and apply silicon spray immediately? I'm not that fond of vaseline as I heard it might eat away at the plastic.

I actually used vaseline first and then silicone next. It wasn't my plan, it was because I didn't know what I was doing. I was looking for a way to lube my storebought and found a couple videos describing how to use vaseline to lube the cube. I thought it really improved the feel of my storebought compared to no lube, but only later did I find that it is not recommended to use vaseline. So I cleaned it all out and bought myself a can of CRC silicone. I can tell you that I am pretty happy with the feel of my storebought today, but I don't know if it was because I used vaseline first for a short while (a few weeks) then washed it out and used silicone from then on.

I have read that some intentionally do this because the vaseline will eat away at the plastic and aid in "breaking in" a storebought. However it seems to me that the sand method would be better and faster than that. And sand has to be much easier to clean up than vaseline.



Question 3: Does it really matter how I'll apply the spray? My first idea was to pop an edge piece out and spray the silicon spray directly into the cube, but I heard that this might damage the screws and springs. Is it better to take apart the cube and spray the pieces and let them dry, or is spraying directly into the cube actually not that bad?
I have always sprayed CRC directly into my storebought cube. I have never laid the pieces out to spray. I have noticed the plastic inside become slightly discolored. The black plastic looks a little gray in parts. My storebought is pretty beat up at this point, and I have some nice cubes on order so I'm not too worried, but I might think twice before spraying directly inside of a nicer cube.

Can anyone back this up? Does the discoloration not happen if you lay out the pieces? Or is this just a side effect of silicone lube?
 
Last edited by a moderator:
Thanks tarpshack for your elaborate answer!

I went to the local store and found this silicone spray, suitable for rubber, plastics, wood and metals.

Gonna apply it in a minute. :D
 
Squirt a little bit in. just a bit. maybe 1 second squirts, twice. And hope this helps:

 
Last edited by a moderator:
CRC isn't the only one out there, but it is good. It's what I use, but that doesn't make it right or wrong, just what I personally prefer.

Lubing a store cube helps it.

A lot of people talk about how you HAVE to take the cube apart to lube it. This really isn't the case. True, you do get a more "Even" coating, but you can lube your cube just as well by popping a few edges. The way I do it is to spray in opposite edges(As in, pop green/white, spray, then blue/yellow, spray, and work in like hell.)
 
Thanks tarpshack for your elaborate answer!

I went to the local store and found this silicone spray, suitable for rubber, plastics, wood and metals.

Gonna apply it in a minute. :D

I have not heard of that spray. I have been really happy with CRC so that's the only thing I use now.

I wasn't aware there was a difference in silicone sprays and actually used Liquid Wrench Silicone Spray first because I found it locally. It was terrible. It caused my cube to seize up and stick instead of making it smoother. Not to mention it had a terrible smell that lingered even after it dried. After that I didn't want to bother trying anything other than CRC or Jig-A-Loo since both came highly recommended from several people in the cubing community.

Hopefully you have better luck with your alternate to CRC than I did.
 
Back
Top