So I just got my first DIY cube

Litz

Regular
Joined
Dec 14, 2009
Messages
216
Location
Portugal
Two actually. I ordered it 2 days ago from cube4you and they arrived today (UPS) in case anyone's wondering. And I live really far so I'm happy with the delivery time.

anyway, since I'm fairly new to this, I didn't want to mess them up (I kinda used vaseline on my storebought).

What do you first do when you get a new cube? Do you assemble it first and play with it for a bit with it really tight? Do you place the stickers right away? Do you lube it as soon as it's assembled?

I just want to make sure I don't ruin these.

Also, I can't really find CRC heavy duty silicone spray or Jig-a-loo in my country. The only silicone spray I found was Arbo silicone spray. Is that fine or do I really need one of the other two?

Thanks in advance
 
Hi, congratulations on your new DIYs

1- assemble with tight tension (try not to put too much pressure)
2- play with it (if you can)
3- adjust tensions for best face rotations (with no pops)
4- play with it
5- lube it (if you want)
6- work it on
7- sticker it

my country is far too, try to find "Cyclo" Silicone spray

hope this helps :)
 
I'd say sticker it before you lube it because you don't want lube to get underneath the stickers and stop them from sticking.

I've always done stickering as the very first thing and never had any problems doing it this way.
 
I'd say sticker it before you lube it because you don't want lube to get underneath the stickers and stop them from sticking.

I've always done stickering as the very first thing and never had any problems doing it this way.

I'm not sure if the silicone getting under stickers will be a problem. I use silicon spray on a rag to get the crap off the pieces, and I've never had stickers peel or slip or anything. Even with 7x7s tiny stickers.

I normally just assemble. Set tensions. Lube. Sticker. Takes no more than half hour. Perhaps my standards are quite low though lol.
 
Ok then, I'll play with them without lube for a while to break them in, thanks.

my country is far too, try to find "Cyclo" Silicone spray

I checked in 5 different places and the only one I found was Arbo silicone spray... You think any silicone spray would do the job?
 
I usually don't lube new cubes until a week later. it helps break them in faster.

^^ I second that.

Lube-wise I used to use Tableau (a spray lube like CRC), but I didn't like the effect of the propellants on the cube. Nowadays I'm using shock oil. Its a pure silicone oil (non-spray) so doesn't cause any 'stickiness'. It works really nicely and you can select among different weights (viscosities) depending on your preference..
 
I've used CRC and Jig A Loo, and they definitely have different effects on the different plastic types. I mainly used CRC but I took a vacation and didn't have my lube with me, so I stopped at Ace Hardware (I had to clean my cube due to dropping it on the beach, so I needed lube!) to pick up some Jig A Loo and man it actually showed visual changes to the plastic where it "melted." There has been a lot of debate whether Jig A Loo is safe or not, well, I still consider it safe, it only pushed off the burs and stuff that were going to get wore off anyway! However it gives my cube a dry feeling, whereas the CRC kept it the typical clicky feeling.

FYI I'm using a Type A core with Type B cubies.
 
If arbo is the only you could get, then you will have to try it if you really wanna lube it, but it will be a pain to wash it if it is bad
 
i think any can has the word "Silicone Spray" will do the job, but sure this dose not include WD-40

some cans says "Siliconized oil" witch you don't want to get, its the same as WD-40

you can also buy silicone lube "Cube Lube" from rubik's website.
 
Alright guys, I'll keep looking for CRC/Jig-a-loo meanwhile since I'm only assembling the cubes on Christmas (can't wait). If I can't find them I'll just buy the other one.

Thanks for the help.
 
Back
Top