Pimpin' out a storebought RBK 3x3

number1failure

Regular
Joined
May 31, 2010
Messages
234
So far, I took a belt sander w/ 80gr sandpaper to the core and cubies. Then finished it up w/ a small piece of 80gr, then 120gr, then 600gr. I have done this so far to the core, a couple corners, and about half the edges. I only have white lithium grease for lube, but I can get another kind easily. When done, I will sticker it with CubeSmith textured tiles. What other things would you guys recommend after sanding to help make it better? And I don't mean better as in popping, smoothness, or anything like that. I just mean OVERALL "better". Also, What lubricant would you recommend? I can get anything <$20,, and that is easily obtainable at a hardware store, WalMart, etc. Thanks for reading and thanks for replying!! (If you reply, that is)
 
So far, I took a belt sander w/ 80gr sandpaper to the core and cubies. Then finished it up w/ a small piece of 80gr, then 120gr, then 600gr. I have done this so far to the core, a couple corners, and about half the edges. I only have white lithium grease for lube, but I can get another kind easily. When done, I will sticker it with CubeSmith textured tiles. What other things would you guys recommend after sanding to help make it better? And I don't mean better as in popping, smoothness, or anything like that. I just mean OVERALL "better". Also, What lubricant would you recommend? I can get anything <$20,, and that is easily obtainable at a hardware store, WalMart, etc. Thanks for reading and thanks for replying!! (If you reply, that is)

Well. I was not aware that cubes possessed a quality called 'better.' I guess I'm not qualified to help you, because I was under the assumption that 'better' was a term that was used to describe a cube that had collectively better smoothness, popping tendencies, etc. than another.

Sorry I can't help!
 
Lube with Vaseline for a bit just to smooth out the pieces. (if parts where you sanded isn't already very smooth)
 
Lube with Vaseline for a bit just to smooth out the pieces. (if parts where you sanded isn't already very smooth)

So the mini, tiny ridges will be smoothed out if I use Vaseline for a short while? If I'm correct doesn't Jig-A-Loo do the same? Also, afterwards should I keep the Vaseline in, clean it out and put in the white lithium grease, or clean it out and put in something else?
 
I dont understand why people spend so much time on breaking into cubes. Buy a cube that is good already damnit.

The price you spend on lube is equal to the price of a good speedcube, already lubed and suitable for your speedcubing needs.
Buy a cheap DIY already and get it over with.
 
I dont understand why people spend so much time on breaking into cubes. Buy a cube that is good already damnit.

The price you spend on lube is equal to the price of a good speedcube, already lubed and suitable for your speedcubing needs.
Buy a cheap DIY already and get it over with.

Fun. Also, if you have something bad, make it better :D

I made mine pretty awesome by moving the U layer about 10 degrees, and pulling down on the pieces below to force a corner cut. Start small, and gradually move further and further out of allignment. If you start at 35/40 degrees, the chance grows that the cube may break. Slowly build up. Do this with all faces. I was travelling to Canberra by car, for an art exhibition, and a sponsor run cubing comp where you had to use Rubik's brand cubes, and I didn't have a diy Rubik's kit, so a few weeks before, I filled the cube with high density sand, and turned it for a few hours until it was smooth and most sand was out. I then washed it completely, and in the 7~ hour car trip to Canberra, I did the trick I mentioned above, as well as grinding it.
I put my right palm to the right face, and left hand gripping the left 2 layers. I press hard on the R face, and do R moves while finding plastic fragrants that cause lockups, and grinding them. I then cleaned the cube out, and it didn't even need lube.

^Hope that helped.
 
I dont understand why people spend so much time on breaking into cubes. Buy a cube that is good already damnit.

The price you spend on lube is equal to the price of a good speedcube, already lubed and suitable for your speedcubing needs.
Buy a cheap DIY already and get it over with.

You don't lube your DIYs?
 
I only have a exacto knife, cant find my sand paper. Anything I can do to the cube ?

The core on this cube is really tight. And my previous rubiks brand cube was sanded down too much... I did mod my AV though, turned out great.
 
I only have a exacto knife, cant find my sand paper. Anything I can do to the cube ?

The core on this cube is really tight. And my previous rubiks brand cube was sanded down too much... I did mod my AV though, turned out great.

You can do the corner mod with the knife. Works great :)
 
I dont understand why people spend so much time on breaking into cubes. Buy a cube that is good already damnit.

The price you spend on lube is equal to the price of a good speedcube, already lubed and suitable for your speedcubing needs.
Buy a cheap DIY already and get it over with.

2qmlsic.png
Maybe they can break it in so they save money?
 
I dont understand why people spend so much time on breaking into cubes. Buy a cube that is good already damnit.

The price you spend on lube is equal to the price of a good speedcube, already lubed and suitable for your speedcubing needs.
Buy a cheap DIY already and get it over with.

I don't see the point of "pimpin'" a rbk storebought anyway.

Making bad cubes into good cubes is fun. It gives you a sense of "Yeah, I made this the way it is, wassup"
 
I dont understand why people spend so much time on breaking into cubes. Buy a cube that is good already damnit.

The price you spend on lube is equal to the price of a good speedcube, already lubed and suitable for your speedcubing needs.
Buy a cheap DIY already and get it over with.

I don't see the point of "pimpin'" a rbk storebought anyway.

Making bad cubes into good cubes is fun. It gives you a sense of "Yeah, I made this the way it is, wassup"

Inorite. Another good thing is, you can show off to people who have a Type B
 
Tried rounding the corners on my storebought, didnt reeally make much of a diffrence. The cube is so tight I have to use a knife to just pop out a piece...

Should I just try to round down the pieces even more? I was carefull when doing this so...
 
Solve it for 1000times, spray with crc and you're done.
Still can't cut corners but that isn't something you can easily improve on.
 
I dont understand why people spend so much time on breaking into cubes. Buy a cube that is good already damnit.

The price you spend on lube is equal to the price of a good speedcube, already lubed and suitable for your speedcubing needs.
Buy a cheap DIY already and get it over with.

I don't see the point of "pimpin'" a rbk storebought anyway.

Making bad cubes into good cubes is fun. It gives you a sense of "Yeah, I made this the way it is, wassup"

Inorite. Another good thing is, you can show off to people who have a Type B

:D
 
Back
Top