NOO What DO I DO?!-Piece missing

RainbowBoy

Veteran
Joined
Jul 21, 2009
Messages
434
WCA ID
2010HUYN01
YouTube
Visit Channel
I own a QJ 4x4- Very good cube! I reccommend it.
And then the corner snapped off from the thing that holds it inside the cube. I don't want to try super glue it back because it might fall off again.
So where do I get a new piece? CubeforYou? What do I DO?!:eek:
 
This type of thing happened with a corner piece in my 5x5 Rubik's Professor. I used a strong superglue. I reassembled it carefully, putting that corner in place early, and finished by popping the final edge pieces in. I suggest you could do the same for your QJ 4x4.
 
This type of thing happened with a corner piece in my 5x5 Rubik's Professor. I used a strong superglue. I reassembled it carefully, putting that corner in place early, and finished by popping the final edge pieces in. I suggest you could do the same for your QJ 4x4.

OK I'll try using super glue and if that doesn't work I'll try get one off iSpinz
 
I finally got my QJ 4x4 two days ago. It turned terrible out of the box and was way too tight.

After 1 minute of turning it, there was a mis-alignment and I couldn't do any double layer turns in any R or L. I took it apart and the core was twisted along it's two halves.

I tried twisting it back into alignment but one of the triangular pieces of the cube snapped off!

I used epoxy and within 30min it was a very strong bond so you might want to try using that. But it back together but it is still tight and turns poorly. I will try giving the parts a light sand to see if it can be looser and smoother.

Cool story right?
 
I finally got my QJ 4x4 two days ago. It turned terrible out of the box and was way too tight.

After 1 minute of turning it, there was a mis-alignment and I couldn't do any double layer turns in any R or L. I took it apart and the core was twisted along it's two halves.

I tried twisting it back into alignment but one of the triangular pieces of the cube snapped off!

I used epoxy and within 30min it was a very strong bond so you might want to try using that. But it back together but it is still tight and turns poorly. I will try giving the parts a light sand to see if it can be looser and smoother.

Cool story right?

Does it have a screw in the core? Loosening that may help, but it won't do a lot.
 
Sorry, off topic but: @Zubon, when I stare at your Display Pic, the tiles seem to contract and... whatever the opposite of contract is; this is especially when I stare at the center white tile in the second row from the bottom.
 
I finally got my QJ 4x4 two days ago. It turned terrible out of the box and was way too tight.

After 1 minute of turning it, there was a mis-alignment and I couldn't do any double layer turns in any R or L. I took it apart and the core was twisted along it's two halves.

I tried twisting it back into alignment but one of the triangular pieces of the cube snapped off!

I used epoxy and within 30min it was a very strong bond so you might want to try using that. But it back together but it is still tight and turns poorly. I will try giving the parts a light sand to see if it can be looser and smoother.

Cool story right?

Dont sand it, QJs have a noticeable breakin period. Give it 20 solves, take it apart and clean the stock oily coating off, do 5 or 10 more and then CRC it and it'll quite possibly be your fastest turning cube.
 
Does it have a screw in the core? Loosening that may help, but it won't do a lot.

Yeah, the two hemispheres are held together by a screw. They became mis-aligned and I thought I could twist them back without loosening the screw. Oh well, it seems to work well now.


@PeterNewton, maybe you need to see a professional about that. :p
 
Back
Top