How to adjust tension??

Deweyspunkis

Regular
Joined
Oct 23, 2010
Messages
67
Location
Everywhere
WCA ID
2011GUEL02
YouTube
Visit Channel
So I just got my F-II in the mail and it's amazing but I just wanted to know, how do you adjust the tension? I opened it up and there is no cap. Also, I searched the forum and found no help so please don't nag me about that, I DID. I'm pretty new to cubing to so I'm not sure if that only on DIY's too. Thanks!
 
You have to remove the center square caps and turn the screws to adjust it. You might have to use a razor blade or something thin to pop them off. But my FII caps just fell off they were so loose.
 
you can probably just drop the cube from a few feet and the caps will pop off. My fII used to do that. Turn the screws left (counter clockwise) to loosen the tension, and right (clockwise) to tighten it. I suggest making quarter turns or less on all sides, then solve the cube a few times to see how it feels, and repeat using smaller and smaller adjustments until you have it how you want it. FIIs work well at tight-medium tensions, in my opinion. Too loose and they pop very easily, with the rounded corners n whatnot. You'll figure it out.

I'm afraid that if I stick a blade in there and pry it it will get lose after and fall out =/

What are you talking about? What will get loose? he's saying prying out the center cap to access the screw, in which case you want the cap to fall out. I guess I'm just confused, you should explain more clearly.

Oh and btw, when you have the caps open, spray some lube (CRC heavy duty silicon works well) onto the screw, or better yet, disassemble the screw-spring structure and lube it all. Makes cubes very, very smooth and fast. Much of the friction is between the screws, springs and washers with the plastic, not just plastic on plastic like the cubies rubbing against one another or the core.
 
Last edited:
As AquaJoe said, remove the thin cap. You may also remove the edges and corners to visualize it and make it easy. I can remove with my nail mines. Be carefull not to damage the plastic with the razor blade.
Note the is a new thred called The one-answer question thread (for Hardware & Buy, Sell, and Trade) to make this kind of questions.
Good luck!
 
Hello.

TO remove the center caps.Force them by your fingernail(Don't try if it doesn't work or else...), or you can use a small knife like this :

Center_Remove.JPG

Also you dont need to worry about the cap falling off! Use this method!

Centercap_dents.JPG

(Make dents)

then adjust the tension.

Then just as Rpotts said:
urn the screws left (counter clockwise) to loosen the tension, and right (clockwise) to tighten it. I suggest making quarter turns or less on all sides, then solve the cube a few times to see how it feels, and repeat using smaller and smaller adjustments until you have it how you want it. FIIs work well at tight-medium tensions, in my opinion. Too loose and they pop very easily, with the rounded corners n whatnot. You'll figure it out.
 
Hello.

TO remove the center caps.Force them by your fingernail(Don't try if it doesn't work or else...), or you can use a small knife like this :

Center_Remove.JPG

Also you dont need to worry about the cap falling off! Use this method!

Centercap_dents.JPG

(Make dents)

then adjust the tension.

Then just as Rpotts said:
That cap is much different from the FII cap
 
This thread is a life saver.
I though my gas assisted sucked because the caps fly everynow and than, but now it's perfect!
 
If the center cap wont stay in place and falls out you can score it with the razor to keep it in place. Do it to all 4 sides. Here is a pic of mine. This also works with the other cubes if you dont want to glue them. Just be careful when you do it.

IMG_0605.jpg
 
Nice tip. I'm going to do that in my Gear cube, the center caps falls all the time and it's very anoying.
 
Back
Top