Does the FII degrade?

Ghosthand I doesn't degrade, unless you overlube it with Jigaloo, then it will just fall apart and shoot itself to death.

Ghosthand I and II are insanely durable, though.
I dropped one from my 8th story building to pavement and the core was fine...

The pieces were chipped in some areas and there were definitive scratches, but DAMN this thing is strong.
 
My fII's core broke when it dropped from my hand (~5 ft) to the concrete street. The yellow center snapped off right at the core. I feel I have dropped cubes like this before without them breaking, but I dunno. I liked it while I i had it, and I never even properly lubed it :(

Mine has dealt with so much more payload than that, its still in good shape
 
My fII's core broke when it dropped from my hand (~5 ft) to the concrete street. The yellow center snapped off right at the core. I feel I have dropped cubes like this before without them breaking, but I dunno. I liked it while I i had it, and I never even properly lubed it :(

Did it have a transparent blue core? If so, it seems that those were breaking much to easily and they started selling them with a more durable core. But then again I've dropped a cube with C4Y hardware from much lower onto a desk and the core broke so it's mostly your fault in this case.

My fII's core broke when it dropped from my hand (~5 ft) to the concrete street. The yellow center snapped off right at the core. I feel I have dropped cubes like this before without them breaking, but I dunno. I liked it while I i had it, and I never even properly lubed it :(

Use a C4U core if you have one. Cores don't make a huge difference in the turning of the cube anyway. Although the core may allow the cube to looser without popping than with the normal core.

I beg to differ. Try using a type C with the original core and then switch it out for a C4Y one. If you don't notice a difference then you're crazy. :D

Ok, well other than type C I with Alpha or C4U core. I'm going to try and refine my post by saying that unless the core is really bad then changing cores won't be a huge difference in turning.
 
That shows normal wear on plastic, if you're saying that the plastic degrades, then fine, you're right. If you're saying that you believe that the function of the cube itself degrades because of plastic wear, then you could possibly be wrong.
That was my most gramatically correct post in weeks.

just saying ;)

on my F-II, all edges have one side more worn out than the other... :confused:

edit: (dun wanna get flamed :( )
My fII's core broke when it dropped from my hand (~5 ft) to the concrete street. The yellow center snapped off right at the core. I feel I have dropped cubes like this before without them breaking, but I dunno. I liked it while I i had it, and I never even properly lubed it :(

Use a C4U core if you have one. Cores don't make a huge difference in the turning of the cube anyway. Although the core may allow the cube to looser without popping than with the normal core.

Well, if you're going to use a C4Y core, make sure you're using the C4Y hardware. If the core in your F-II is blue (not the gray one) then the screws will be much to long. i think. I have a F-II with a broken core. I've used a random kernal i got from one of those toronto competitions, and C4Y hardware. It was really hard to turn, yet it still popped. Just today, I've switched to using that cube with old Type A Core and Hardware, but since the screws are really long, it pops a lot.
 
Last edited:
I find the plastic is very soft and I have had to tighten mine quite a few times to keep it from becoming too loose. I bought a backup one just in case my main speedcube dies, but let's hope that doesn't happen.

The soft plastic issue is the main problem I have with my FII. Currently I use it as my 'weekend' cube. Over the period the cube seems to become stiff, as if it has a lot of fine dirt in it. The cube needs to be re-lubed before every weekend (after 2-days of use) and also needs a full clean every month or so (8-days of use) to prevent it getting too stiff. Does anyone else get this problem?

Not at all loosen it up, it doesn't pop.


One ridge on an edge piece is higher than the other one. This is why the ridge on one side of your edge piece is lower than the other one.
yeah someone else said that and I just got a new FII and that's true. hopefully the F-III fixes this and has end caps that STAY ON.

my new FII seems REALLY light compared to my worn out one. also it seems lighter than it was when it was what I considered it's prime. obviously it's not lighter, just feels lighter.
 
Back
Top