Alpha Chun and the alpha core

SenileGenXer

Regular
Joined
Mar 7, 2012
Messages
206
Location
Virginia, USA
I know there has been a little talk about these on the zcube.cn thread but I want to focus on the Alpha Chun cubes and the Alpha core.

If you go to zcube.cn and look at cube brand Alpha here
You will see the two Alpha Chuns and a red thing called the Alpha Core.

Big question how does the Alpha core work? Those aren't screws. What do all the plastic washers do? Are the Chun cubes better with the core?

Cm_Hu chimed in on a previous thread and said the designer Chun was working on a system where the chun cubes would be interchangeable with each-other and with the core. I am really interested as I have heard they are a small light cube but is this complexity a bonus? I know a few people ordered the cube but I haven't heard an opinion.
 
Last edited:
I have a Chun1 and it's pretty awful - very catchy and locky. The metal bits are a nice gimmick but they do nothing to improve what is a poor cube. No idea about the cores.
 
Chun 2 have a regular core and regular screws, and it is the most unstable/flimsy/airy cube I have ever tried, but it's super fast, since nothing is touch! :)
mine came with 3-4 different sets of springs, so I might just have chosen the "wrong" ones..!?

it kinda feels a bit like a bad version of the ShuangRen! :)
 
Were there six of each kind spring? Could it have been springs for the centers and also springs for the metal bits on the edge pieces?
 
If there were enough springs perhaps they are supposed to get packed inside the edge pieces pushing out against the metal bits. It cause some friction, contact or lock against the corner pieces when in position but not for the other parts of the turn.
 
Last edited:
I have these different Chun cubes and have a couple with the different core in it for comparison. I have to agree that the metal bits seem a bit pointless. They dont fit well into the pieces in many cases(most frustrating, they sometimes fall out during assembly or have bits that arent flush, but once you have them set acceptably, they slightly change the feel for the better compared to them not being there at all due to the cube being a bit heavier and feeling more solid. Without them in there it feels very light and hollow, similar to an Alpha CC without the extra hardware.

I did experiment with the different springs, and found I like the medium ones best, the light ones made the cube prone to popping unless you made it really tight, which kind of defeated the point of the lighter springs I suppose.

The idea of the core is a good one, the implementation not so much. Imagine a screw shape item with complete metal circles around it as opposed to a screw thread. The head of the (Ill call it a screw despite its lack of thread because I dont know the correct term) screw sits inside the core, with a spring so there is no spring outside of the core. Pulling on the "screw" will compress the spring between the head of the "screw" and the inside wall of the core. You put a plastic bit that comes in two halves around the metal ring (instead of the screw threads) that corresponds to the tension (length of working screw) you want. This is then secured with an incredibly fiddly collar that holds the two parts together. The benefit of this is that you can with absolute certainty set each side to the same tension, simply by putting the collar around the same metal circle. The downside to this is it is profoundly irritating to put together (the guy in the video on the website makes it look incredible easy, its blatantly not) and to adjust the tension if you dont like it after it is set involves taking off each collar, moving the plastic circle to a new place and reassembling it again. This is difficult to do as the screws pull against the pieces at the tensions you want (obviously), so you have to drag out a bit of thread against the pull of the spring, and hold it in place as you assemble the annoyingly fiddly plastic circle and collar arrangement around the metal ring you want. Against the tension this is a tricky but not insurmountable business. However it will annoy you if you get it all set up and then decide you dont like the tension, since you have to go through this whole rigmarole again when ususally you would simply turn 6 screws a half turn or whatever.

The other problem is the inability to fine tune it in any meaningful way. I found myself in a situation where position a was slightly too tight, and position b (the next position) slightly too loose. Since this is a digital rather than analogue tensioning method, there simply is no middle ground, and as mentioned before, trying different tensions out involves the annoying setup process alluded to before.

Ultimately I now have four chun cubes (two with the core, two without) and I have found an acceptable tension (not perfect, just the least bad of the options available) and its OKish. They feel very like other recent alpha cubes (e.g. cc), light and a little flimsy. They are a very loud, bit locky, have good corner cutting with a bit of lube, but arent really a patch on a dayan or shaungren. If you are in the market for a new alpha, the cc3 is your best bet. if you want a chun, the chun 1 works better for me, even if I find myself popping the odd metal bit back in every few solves. Regarding the chun core, if you are prepared to put up with ordeal of putting it together, perhaps a few times then you are guaranteed the same tension for each side (good), but you wont have the level of control over those tensions that you may want (not so good), and its a massive pain to put together (really really annoying). If you must get one, my chun 1 works best with it, I think its a better cube than the chun 2. I have ound a tension I can live with, so its OK, but it is no world beater.

I just want to say I applaud the innovation that has gone into the core/cube. They have really tried to do something different rather than out Dayan Dayan. I will be buying the next iteration as and when it comes up (because I just buy all the 3x3s!) and hope they can improve on a design that if nothing else, certainly has potential.
 
I have the Chun2, and i really like it alot. :-) I'm not really a speedsolver, but i don't really get any problem with lockups. It got good corner cutting, regular and reverse.
I only find two cons with this cube tough, and the first thing is the feeling. It feels... a bit strange. Can't really explain the feeling.
The other con is that ONE metallic piece is jumping out all the time, but that might be because i bent some pieces when it arrived since i didn't really know how to assemble it. But that pop is probably because of that bend.
Otherwise, i personally think it's a nice cube. :-)
 
Thank you speedpicker and everyone else who explained their experiences.

I bought an Alpha Chun 2 and managed to put it together very well including finding a way to insert the metal parts so they stayed without glue. They really stayed, I haven't had a metal part pop in the week I've had it and this is a Chun 2 where the metal parts don't fit. I also made a "squeeze mod" that toned down the clicking action on the cube.


Hope other people find it useful. I'm sorry for the slow pace and horrible cubing on display. I wasn't trying to speed solve just talk and solve and I failed at that.
 
Last edited by a moderator:
Back
Top