Search results

So basically, I'm trying to find any block trainers that aren't cubegrass for a few reasons, in regards to Petrus blocks. It has 222 and 322 expansion, but unfortunately, the 222 is built in UFR which is a horrible place, and it also doesn't have anything for direct solving the 322. If there...

As the title states, I am curious as to why people claim Petrus is bad. It has relatively good ergonomics, its efficient and has a good last layer than can be 1 looked with relative ease. I myself average around 10 with it, though I was sub-10 not too long ago (damn breaks) and I just struggle...

Probably would have been lower if I didn't mess up the last two solves...

ugh, kill me. Second one this week.

Finally got it, after around 4 months of hardcore Petrus practice! Generated By csTimer on 2017-10-27 single: 5.14 Time List: 1. 5.14 F2 L2 D2 L2 D2 R2 B L2 B R2 L' D B2 R D R' B' F2 L Reconstruction: R' y U' L' U' L R' U y L F' L' y //3x2x2 R U' R2' F R y' // EO R U2 R2 U' R U' R U2 R' U R...

Generated By csTimer on 2017-9-16 single: 8.83 Time List: 1. 8.83 D B D L2 B2 R F' R2 L2 U B' D2 R2 B D2 L2 F U2 B L2 Reconstruction: z2 y' // Inspection R F //2x2x2 y2 U' R U R2' U' R// 3x2x2 F2 R U' R' L' U L2 F' L' F// EO R' U R U2 R U2 R U R' U' R U R' U' R U R'//F2L U' L' U' L...

So, as the title says, this will be guidelines on how to get faster at the Petrus method. Unfortunately the Petrus method has very low usage, but since switching to it in the past month my averages are within one second of my CFOP times. anyway, here we go! First and foremost, the most...

So, I've gotten a little bored of the big four methods, and want to try something new, like L2LK. Unfortunately, I don't know the best approach to learning the algorithms. I know ELL, so that's 27 algs down, but I'm not sure if I should just go in order of learning the algs step by step, and is...

Getting better, any tips would be appreciated. Generated By csTimer on 2017-3-19 avg of 5: 16.22 Time List: 1. 17.97 U2 L2 B2 R' B2 R B2 D2 B2 F2 R2 B L B2 R' U2 F' U R D' L 2. (22.38) F2 D2 B' R2 B' D2 U2 F2 D2 L2 D2 U B' D R D L2 B' U' R2 3. 14.12 U2 L F2 D2 U2 R' F2 R2 F2 R' F' L...

Couple of lucky solves, but any advice will be taken! Cube: DaYan LunHui Scrambles: Generated By csTimer on 2016-5-16 avg of 5: 12.16 Time List: 1. 13.24 R' U' D' L2 D' L' F' R2 D' L2 U2 F2 B U2 F L2 F' B' L2 U2 2. 11.83 D2 F2 D2 U2 L' U2 L F2 R U2 D B' R U' F2 R2 F' R2 U F' 3. (10.96)...

Could I get a reconstruction on the 12.67?

Alright. This method is based off of the idea that blocks are good. Anyway. First off the steps of the advanced method: 1. F2B-1 2. finish F2L-1 while solving EO 3. place FDR 4.WVCP 5.L5E Pros: Cons The steps of the intermediate: EOline: same first step as that in ZZ. Not too difficult to...

Ok. When I first got this puzzle,I when straight in to first turns. The first turns are very scratchy, but not dry. The cube out of the box was very tight, and was still capable of 45 forward, 3/4 reverse corner-cutting. The only problem I have with this cube, is even on fairly loose tensions...

Two questions. 1. title (Last 5 corners) 2. would it be suitable for speedsolving? (probably not) What I think it is: 5!*3^4/15. Is this correct? EDIT: What would it be if a certain corner were in a certain spot everytime? i.e Setup R U R' U' The FDR corner is always in URF. How many cases...

This cube measures 57mm across, and only comes with a stickerless option. Corner-cutting is decent, about 40 degrees forward and half a cubie reverse. The turning feel changes once all the stock lube is removed. It goes from a smooth and controllable cube, to a crunchy and faster cube. After...

Hi everyone. First and foremost, I apologize if this is in the wrong place, has been thought of, etc. Now, for the actual method itself, it goes as follows, with the approximated movecount following the step: EOline:8 LD 1x2x3 block: 12 CP:10 BDR 1x2x2 (R,U): 7 LPELL:7 2GLL:13 Total approximated...

I have a rough turning style, and was wondering if it is possible to change it. Check out my youtube channels and some of the videos for and idea on my turning style.

Hi. I am currently working on a new 3x3. It will be made entirely in Autodesk123D and will be printed by shapeways. I started today, and currently have made very little progress. Wish me luck! (I'll need it).

title. To my knowledge there aren't that many in northern Illinois, or southern Wisconsin

title. basically, what brand is it (MoYu, YJ, Fangshi, YuXin, etc.)