One Answer Hardware Question Thread

That doesn't work with my Yue Xiao. My tensions might be a little tighter than yours. But due to the antipop mechanism it doesn't come apart.

 

Does anyone know where one can actually buy the sticker sets Gans uses for their advanced and master cubes? I really love them and can't find a website or anything.

 

Okay so this tells me that your tensions are too tight. I recommend loosening it to the tensions I described and then try to take it apart. You'll want to take the screws out anyway to lube the hardware, though. There are some great video tutorials on YouTube. Hope this helps!

 

Sorry, that didn't help at all. I didn't ask for help regarding tensions or lubing. I asked for a way to disassemble the cube without loosening the screws.
These newer cubes' antipop mechanisms make it really hard to take them apart.
Here's what I did: I loosened one screw by 360 degrees. That was enough to get a piece out. When I reassembled the cube, I had to loosen the screw by another 360 degrees to get the last piece back in. In the end I tightened the screw by 720 degrees. Seems to have worked out just fine.

 

I want to start modding some cubes but I do not know where to buy epoxy.

 

https://lmgtfy.com/?q=where+to+buy+epoxy

 

I'm new to the forums, so I'm not quite sure if this should go in the hardware section....but I plan to buy a guoguan(I'm a sub-20 solver), and are the stickers on the guoguan good? I know it hasnt been out long, so if anyone has chipped stickers already could they let me know? My cubes have all been stickerless.

 

The GuoGuan stickers are very good. I replaced mine with my own shades, but when I did, I noticed the stock stickers were pretty heavy duty.

 

For molding your cubes, you may try looking what's suitable for you here: https://www.alibaba.com/showroom/epoxy-resin-plastic-led-cube.html

 

Corner broke

Is this a problem?

 

That is absolutely a problem ...... Unless..... You may be able to super glue the piece back on there until you get a new corner. I've done that in a pinch. I wish you the best. Which puzzle was it?

 

Qiyi Thunderclap

it still turns fine, i'm just scared there might be problems later. others corners could also break

 

Hi, old cuber here, I am trying to find out what 4x4 this cube is. http://imgur.com/a/sasxN

Also is the Yuxin 4x4 the best right now?

 

That's a Moyu AoSu. I have the same one in white. It's many people's favorite. But the Yuxin Blue 4x4 (not the "Yuxin 4x4") has convinced many cubers to adopt it as their new main after a Thunderclap V2 spring swap. However, QiYi just released the Wuque, and it's taking the 4x4 event to a whole new level. In fact, I would recommend the QiYi Wuque, but I haven't received mine in the mail yet. But after seeing pictures of the mechanism, and seeing all the videos, I'm pretty confident that it'll kill my AoSu and Yuxin Blue.
I also have a Cyclone Boys G4 stickerless and I really like it, too. I had to sand down all the flash, break it in, and do a spring swap before it got good and now it's my favorite 60mm 4x4.
In summary, skip Yuxin and go for the QiYi Wuque.

 

Yeah, just go ahead and get another one and use the new one for parts. You don't want to mess up any other pieces of your perfectly broken in cube.

 

I am planning to buy Valk 3, weilong Square 1 and Moyu magnetic skewb.

I know that zcube sticker has a valk fitting sticker but I cant find weilong square 1's sticker

Does Zcube Square 1 sticker fits on the weilong square 1?

and does the Standard Moyu skewb fits on the moyu magnetic skewb?

 

If I remember correctly, the QiYi Squan is 55mm cubic, and the Weilong Squan is 54x54x56mm. Since the QiYi has really been the only 'good' squan until recently, I'd expect standard squan stickers to be fitted for it... So I don't think they'd fit the Weilong.
That's not to say they wouldn't work, they just might look a little wonky.

As for the skewb, TheCubicle lists their standard MoYu skewb stickers for both MoYu's normal and magnetic skewb, so I don't think there should be a problem.

 

Why the weilong (gts) 2x2 comes in stickerless but the 3x3 don't, and the guoguan 2x2 doesn't come in stickerless but the 3x3 does? It's very hard to understand and for people who collect whole series of cubes (in stickerless version) this is very annoying.

 

Stickerless weilong 3x3 here
http://cubezz.com/Buy-4562-MoYu+WeiLong+Version+II+Stickerless+Speed+Cube+57mm+Standard+Color.html

 

Weilong V2s do come in stickerless. I believe the Guoguan 2x2 is a capped design so you probably won't see a stickerless version of it